#FORD ENGINE CODES P2176 SERIAL NUMBER#
#FORD ENGINE CODES P2176 UPDATE#
#FORD ENGINE CODES P2176 FULL#

Take care not apply to much sealer at the two ends of the weatherstrip and remove any excess. The solution is to apply sealear to the gap along the length of the weatherstrip. Solution: The most likely cause is the upper weatherstrip of the windscreen vibrating against the metal of the roof panel. Problem: Whistling noises during high speed form upper windscreen area. The bracket will need to be realigned and tighten the four bolts to 23Nm. Solution: The A/C (air conditioning) compressor supporting bracket works its way loose.

Problem: Excessive noise from the accessory drive belt. Revised bolts should be fitted and tightened to 24 Nm.ДЇord Fiesta and Focus 2001 - 2002 1.8 TDCi and Di engines with A/C Solution: The most likely cause is the port 4 upper and lower exhaust manifold bolts working loose. Problem: Exhaust gas leak from exhaust manifold. Updated and more reliable calibrations will set the engine revs to increase by 100 rpm when the AC is switched on and an extra 150 rpm when the AC is running in high temperaure environments.ДЇord Focus and Fiesta 1.8 Endura diesel engine 2001

#FORD ENGINE CODES P2176 UPDATE#

The PCM will need a software update if the part number precedes: However, due to PCM (engine control module) software issues, the increase can happen with the AC switched off or even in cars without AC. Solution: At high temperature environments, the engine increases the engine revs by 250 rpm to increase the air conditioning performance. Problem: Intermittent rough engine idle at high ambient temperatures. The revised flap has been fitted since 06/2003. To rectify the problem, a revised air distribution flap should be fitted. SOlution: A known problem is a faulty air distribtion flap. Problem: When the fan direction is set to windscreen, air is still blown into the footwell. P0653 вЂ“ Sensor voltage supply circuit 2 short to battery P0652 вЂ“ Sensor voltage supply circuit 2 short to ground or open circuit P0651 вЂ“ Sensor voltage supply circuit 2 noisy signal P0643 вЂ“ Sensor voltage supply circuit 1 short to battery P0642 вЂ“ Sensor voltage supply circuit 1 short to ground or open circuit P0641 вЂ“ Sensor voltage supply circuit 1 noisy signal If there is inteferance or the voltage is not regulated correctly, the signal for pedals or throttle body will be out of range P2108 can relate to mass air flow, engine speed, pedal ratio, TPS ratio, torque generation, engine speed limitation etc. This can be a number of different sensors and will often be triggered with other fault codes that are more specific. P2107 - Processor monitoring on the main controller fault Fault in circuit between throttle body motor and PCM. If other fault codes are stored, they should be investigated first before P2176.

#FORD ENGINE CODES P2176 FULL#

This confirms correct functioning of the throttle body through the full range. After the ignition is switched off, the throttle body will run through an adaption cycle and spring check. This can be from an obstruction or incorrect signal. The throttle flap has not moved to the required position.

P2119 вЂ“ Throttle plate convergence error. P2135 вЂ“ Throttle position sensor ratio error P0223 вЂ“ Throttle position sensor 2 electrical error short to battery P0222 вЂ“ Throttle position sensor 2 electrical error short to ground or open circuit P0220 вЂ“ Throttle position sensor 2 electrical error P0123 вЂ“ Throttle position sensor 1 electrical error short to battery or line break P0122 вЂ“ Throttle position sensor 1 electrical error short to ground P0120 вЂ“ Throttle position sensor 1 electrical error P2128 вЂ“ Pedal sensor 2 electrical error short to battery P2127 вЂ“ Pedal sensor 2 electrical error short to ground or open circuit P2123 вЂ“ Pedal sensor 1 electrical error short to battery P2122 вЂ“ Pedal sensor 1 electrical error short to ground or open circuit

#FORD ENGINE CODES P2176 SERIAL NUMBER#

Replace with a revised throttle body of the serial number is below 400000. Check the serial number on the throttle body. The throttle body will need to be inspected and tested using an scope or scanner looking at live data. On vehicles that trigger P2119, P2135, P2176, P0120, P0122, P0123, P0220, P0222 or P0223 fault codes can suffer from the same PCM terminal damage but also suffer from throttle body electrical connector damage. Check the electrical connector for the PCM for damage to the terminals and pins. Vehicles that trigger diagnostic fault codes (DTCs) / fault codes P2138 with P2122, P2123 or P2127 a common problem is the PCM (powertrain control module = ECM = engine control module) electrical connector. Solution: The EAC FAIL relates to the electronic accelerator control. Problem: Loss of power and EAC FAIL displayed. Revised and updated new shock absorber top mounts should be fitted.ДЇord Fiesta & Fusion upto 2003 1.25 1.4 1.6 Duratec Solution: The most likely problem is the shock absorber top mounts. Problem: Knock from rear suspension on rough road surfaces. Ford Fiesta Common Problems Solutions Hints and Tips

Ford engine codes p2176